您好,欢迎光临莱州中科聚峰机械有限公司网站! 主营自动搅拌车,搅拌一体车,自动上料搅拌车等各种规格的产品。

自动上料搅拌车行业持续领跑者!

点击拨打服务热线:4008791999

您的位置:首页 - 新闻中心 > 行业资讯 >

自动搅拌车格各种阀门生产的作用

发布时间:2021-09-13 来源:http://www.jfhntjbc.com/ 浏览量:

概述:使用前应做到Before use1、检查各个水箱是否缺水并加足水,轮胎气压是否符合2 5bar以_上要求。1 Check whether each water tank is
使用前应做到
Before use
1、检查各个水箱是否缺水并加足水,轮胎气压是否符合2.5bar以_上要求。
1. Check whether each water tank is short of water, add enough water, and whether the tire pressure meets 2.5bar_ The above requirements.
2、检查发动机机油油尺,液压油箱标尺,齿轮箱油标观察孔,前、后桥,轮边减速轴头拧开油面油堵检查齿轮油是否符合要求,缺少应及时添加,总泵自动液油杯液面是否合乎标准要求。
2. Check the engine oil dipstick, hydraulic oil tank dipstick, gearbox oil indicator observation hole, front and rear axles, wheel side reduction shaft head, unscrew the oil level oil plug, check whether the gear oil meets the requirements, add it in time if it is missing, and whether the liquid level of the automatic oil cup of the master cylinder meets the standard requirements.
3、观测发动机机油,齿轮油,检查油标尺,油标锣孔,液压油箱时,车辆要水平位置。
3. Observe the engine oil and gear oil, and check the oil dipstick, oil pointer, Gong hole and hydraulic oil tank. The vehicle shall be in a horizontal position.
自动搅拌车
4、全车各部油管路,气管路接头是松动有无漏油,漏气现象。检查全车线路有无接触不良,各仪表,灯光是否工作正常。
4. The joints of oil and gas pipelines of all parts of the vehicle are loose, and whether there is oil and air leakage. Check whether the circuit of the whole vehicle has poor contact and whether all instruments and lights work normally.
生产的各操作阀的作用
Function of each operating valve produced
1、主车前后行走操纵阀( 快慢档,前进和倒车档)-般行走时为前驾,施工作业时为后驾。
1. The front and rear travel control valves of the main vehicle (fast and slow gears, forward and reverse gears) - generally, it is front drive during walking and rear drive during construction.
2、大臂升降旋转操纵阀,举料,左右旋转罐体控制。
2. Boom lifting rotary control valve, material lifting, left and right rotating can body control.
3、料斗上下料操纵阀,铲料、卸料控制铲斗作用。
3. Hopper loading and unloading control valve, shovel and discharge control bucket function.
4、手动油门操纵阀,控制发动机的转速,使搅罐在一定的平稳速度下旋转。
4. The manual throttle control valve controls the engine speed to make the mixing tank rotate at a certain stable speed.
5、座椅脚踏定位卡销,用于座椅调转方向时起到锁止作用,踏板踩向下时。锁销打开,左翼转到位置后制动锁止
5. The seat pedal positioning detent is used to lock the seat when turning the direction, and when the pedal is pressed down. The locking pin is opened and the brake is locked after the left wing is turned to the position
今天小编给大家呈现就是关于自动搅拌车的相关知识,如果您对于本文有什么疑问及问题欢迎来电咨询或者网站下边留言:http://www.jfhntjbc.com
Today, Xiaobian presents you the relevant knowledge about automatic mixer truck. If you have any questions and questions about this article, please call us or leave a message below the website: http://www.jfhntjbc.com

截屏,微信识别二维码

微信号:

点击微信号复制,添加好友

 打开微信