自动上料搅拌车一般在放料完成后，卸料部分会残留许多混凝土，一般情况下用清水清理即可，可是遇到已经凝固在自动上料搅拌车上的情况下，我们该怎么办？

Generally, after the automatic feeding mixer is completed, there will be a lot of concrete left in the unloading part, which can be cleaned with clean water under normal circumstances. But what should we do if it has solidified on the automatic feeding mixer?

自动上料搅拌车在完成方料后就应当进行清洗保养及维护，以免降低自动上料搅拌车的使用寿命，许多搅拌车司机们也知道这个道理，也经常对自动上料搅拌车卸料部分进行清理维护，但是有一个问题就是大家往往忽略的，就是用不好用不对清洗液也是会造成卸料部分损坏的。

The automatic feeding mixer should be cleaned, maintained and maintained after the completion of the square feeding, so as not to reduce the service life of the automatic feeding mixer. Many mixer drivers also know this truth, and often clean and maintain the unloading part of the automatic feeding mixer. However, one problem that is often overlooked is that the unloading part will be damaged even if the cleaning fluid is not used properly.

1、用好的清洗液，掌握正确的方法，适当用量，正确的使用标准可以参考清洗液的说明书，而且要适量，否则清洗液里面的化学成分会损坏自动上料搅拌车的相关结果。

1. Use a good cleaning solution, master the correct method, use the appropriate amount, and refer to the cleaning solution manual for the correct use standard, and use the appropriate amount, otherwise the chemical composition in the cleaning solution will damage the relevant results of the automatic feeding mixer.

2、选择清洗液，一般用常见的碱性溶液，不要使用化学成分高的，浓度高的清洗产品。自动上料搅拌车在日常生活中是使用非常频繁的，所以，清洗自动上料搅拌车也是相当重要的。

2. Choose cleaning solution, generally use common alkaline solution, and do not use cleaning products with high chemical composition and concentration. The automatic feeding mixer is used very frequently in daily life, so it is very important to clean the automatic feeding mixer.

此外托轮也要保养好，搅拌车的托轮要定期补加润滑脂，托轮的表面要经常清理附着在上面的混凝土，然后注油，这样可以避免托轮的磨损，延长使用寿命。

In addition, the supporting wheel should also be well maintained. The supporting wheel of the mixer truck should be regularly added with lubricating grease. The surface of the supporting wheel should be regularly cleaned of the concrete attached to it, and then filled with oil. This can avoid the wear of the supporting wheel and prolong its service life.

自动上料搅拌车的散热器也是保养的，每天检查散热器的风扇是否正常运转，对叶片上的灰尘及时清洗，散热器的过滤芯要定期更换，滤芯精度要与原装滤芯保持一致。

The radiator of the automatic feeding mixer is also the focus of maintenance. Check whether the radiator fan operates normally every day, clean the dust on the blade in time, replace the filter element of the radiator regularly, and keep the accuracy of the filter element consistent with the original filter element.

液压泵的保养，液压油须保证清洁，平时一定要避免泥沙污水进入液压油内，一旦发现液压油和液压零部件上有污水泥沙，就立刻清洗并更换液压油。更多相关内容就来我们网站http://www.jfhntjbc.com咨询吧！

For the maintenance of hydraulic pump, the hydraulic oil must be kept clean, and sediment and sewage must be avoided from entering the hydraulic oil at ordinary times. Once sewage and sediment are found on the hydraulic oil and hydraulic parts, the hydraulic oil shall be cleaned and replaced immediately. More relevant content will come to our website http://www.jfhntjbc.com Consult!