搅拌一体车重要部件机架起到有效作用，所以需要对其进行充分的了解，对后期的有效使用打好基础。下面来讲讲相关内容吧。

　　The important parts of the mixing vehicle frame play an effective role, so it is necessary to fully understand it, to lay a good foundation for the effective use of late. Let's talk about the relevant content.

　　搅拌一体车的驱动装置就是通过机架安装在搅拌设备封头上的，机架内应有足够的空间，以容纳联轴器、轴封装置等部件，并保证安装、操作所需的空间。大多数情况下，机架中间还要安装中间轴承装置，以改善搅拌轴的支承条件。根据不同工况和不同支撑的要求，一般分为无支点机架、单支点机架和双支点机架三种。

　　The driving device of the mixing vehicle is installed on the mixing equipment head through the frame. There should be enough space in the frame to accommodate the coupling, shaft sealing device and other parts, and ensure the space required for installation and operation. In most cases, intermediate bearing devices should be installed in the middle of the frame to improve the support conditions of the mixing shaft. According to different working conditions and different support requirements, generally divided into non-fulcrum frame, single fulcrum frame and double fulcrum frame three.

　　无支点机架：本身无支承点，以减速机输出的两个轴承支点作为支撑，适用于轴向力较小或仅受径向力，搅拌载荷均匀的场合。

　　Non-fulcrum frame: it has no supporting point and is supported by two bearing fulcrum outputs of reducer. It is suitable for the occasions where the axial force is small or only receives radial force and the stirring load is uniform.

　　单支点机架：机架本身设有一个支承，能承受双向载荷，轴向载荷可以全部卸到机架支承上，能保证减速机的传动质量，延长减速机的使用寿命，是应用广泛的一种机架，适用于均匀负载，中等冲击的场合。

　　Single fulcrum frame: the frame itself is provided with a support, can bear bidirectional load, axial load can be all unloaded to the frame support, can ensure the transmission quality of reducer, prolong the service life of reducer, is a widely used frame, suitable for uniform load, medium impact occasions.

　　双支点机架：机架中间设有两个独立支承，适用于重的冲击载荷及对搅拌密封装置有较高要求的特殊场合。

　　Double fulcrum frame: there are two independent supports in the middle of the frame, which is suitable for heavy impact load and special occasions with high requirements for mixing and sealing device.

　　单支点机架或双支点机架，配用三分式联轴器，可在不拆除减速机和机架的条件下拆除及更换机械密封。还有一种机架，机架带有提升装置，可不拆除电动机、减速机，而是将其整体旋转，进行机械密封的检修和更换，可减轻设备维护的工作量。

　　A single or double fulcrum frame with a three-part coupling can remove and replace the mechanical seal without removing the reducer and the frame. There is also a frame, the frame with lifting device, can not remove the motor, reducer, but the overall rotation, mechanical seal maintenance and replacement, can reduce the workload of equipment maintenance.

　　当然为了更好的进行使用，需要定期对搅拌一体车以及它的部件进行检查维护工作，包括日常保养的工作内容外，尚需拆检离合器，检查和调整制动间隙，如离合器内、外制动带磨损过甚须更换。此外，还需检查钢丝绳，V带滑动轴承，配水系统和行走轮等；须检查搅拌叶片和刮板与衬板之间的间隙，上料斗和卸料门的密封及灵活情况。等等。

　　Of course, in order to better use, it is necessary to regularly check and maintain the foot car and its parts, including the daily maintenance of the work content, still need to disassemble the clutch, check and adjust the brake clearance, such as the clutch inside and outside the brake belt wear must be replaced. In addition, it is necessary to check the wire rope, v-belt sliding bearing, water distribution system and walking wheel, etc. Check the clearance between the mixing blade and the scraper and the lining, the sealing and flexibility of the hopper and discharge door. And so on,

　　搅拌一体车重要部件机架起到有效作用的相关内容便是这样了，如果您想提高一体车的工作效率就需要多了解有关知识，更多资讯就来网站www.jfhntjbc.com看看吧。

　　Mixing integral vehicle important parts of the frame to play an effective role in the relevant content is such, if you want to improve the efficiency of the integral vehicle you need to know more about the knowledge, more information to the website www.jfhntjbc.com see it.