During the daily operation of the automatic feeding mixer, it may encounter the situation of sudden ignition and power failure, so how to deal with it at this time? Let's read about it.

　　自动上料搅拌机是一种在筒体或罐体中用叶片旋转轴，将多种原料搅拌混合，使其成为混合物或合适稠度的机器。广泛应用于涂料、固体、油墨、颜料、胶粘剂等化工产品的搅拌、分散、溶解的设备。

　　Automatic feeding mixer is a machine in a cylinder or tank with blades rotating shaft, mixing a variety of raw materials, so that it becomes a mixture or a suitable consistency. Widely used in coating, solid, ink, pigment, adhesives and other chemical products of stirring, dispersing, dissolving efficient equipment.

　　自动上料搅拌机的料斗在上升过程中如果突然停电也没关系，因为上面会有刹车，可以及时有效的控制。如果在运行过??程中突然断电，要立即关闭自动上料搅拌机的主电机和上料系统的总开关，并将所有调速旋钮调到原位。

　　If the hopper of automatic feeding mixer is in the process of rising, it does not matter if there is a sudden power failure, because there will be brakes on it, which can be timely and effectively controlled. If running?? During the process of sudden power failure, first of all, to immediately close the main motor of the automatic feeding mixer and the main switch of the feeding system, and adjust all speed control knobs to the original position.

　　如果自动上料搅拌车在满负荷运行时突然断电或发生故障，应先将开关拉下，手动清理搅拌筒内的混凝土。控制要求不允许搅拌机带载启动，以防止启动时因电流过大损坏电机。自动上料搅拌车操作简单，要在有木板的操作台上操作。启动时，如发生火灾或电压突然下降等情况，应立即停止启动，切断电源，并进行检查维修。

　　If the automatic feeding mixer is suddenly powered off or fails when it is running at full load, the switch should be pulled down first and the concrete in the mixing cylinder should be cleaned manually. The control requirements do not allow the mixer to start with load, in order to prevent the motor from being damaged due to excessive current when starting. Automatic feeding agitator is simple to operate and must be operated on a board operating table. When starting, in case of fire or sudden voltage drop, stop starting immediately, cut off the power supply, and check and repair.

　　如果停电时间比较短，在恢复供电时，注意将料筒加热到工艺温度后，保持一段时间的恒温。然后测试真石漆设备的旋转阻力。如果比较容易，打开低速电机继续工作。如果设备启动时转速不稳定，应立即停机查明原因，排除故障后再启动运行。

　　If the power failure time is short, when restoring the power supply, pay attention to heating the barrel to the process temperature, and keep the constant temperature for a period of time. Then test the rotary resistance of the lacquer equipment. If it is easier, turn on the low speed motor and continue working. If the speed of the equipment is not stable when starting, it should be stopped immediately to find out the cause, and then start running after troubleshooting.

　　如果停电时间较长，需要停产，则应清洗桶内原料和桶内。待自动上料搅拌机冷却后，整理机内原料，再将机内筒体上的粘料清理干净。清洗后，可以在真石漆设备内部涂上一层防锈油，将机器放在通风干燥的地方，下次继续生产。

　　If the power outage is long and production needs to be stopped, the raw materials and barrels should be cleaned. After the automatic feeding mixer is cooled, the raw materials in the machine will be sorted out, and then the adhesive material on the barrel body will be cleaned up. After cleaning, you can coat the interior of the lacquer equipment with a layer of anti-rust oil, put the machine in a ventilated and dry place, and continue to produce the next time.

　　总而言之，自动上料搅拌车在作业中会遇到各式各样的突发状况，我们只有认真做好设备的养护和维修，才能保证设备稳定的运行。更多自动上料搅拌车详细咨询，请继续关注http://www.jfhntjbc.com网站吧。

　　In a word, the automatic feeding mixer will encounter all kinds of emergencies in the operation. Only by carefully maintaining and maintaining the equipment can we ensure the efficient and stable operation of the equipment. For more details on automatic feeding mixer, please continue to pay attention to http://www.jfhntjbc.com.